Case Study of the MCIS 4: Mr. AXE

Analysis of Mr. AXE’s MCIS

Mr. AXE’s MCIS (Meta Consciousness Implementation System) is set to accept lights in bulk. In other words, a whole stack of light comes into MCIS through Baeg-Hwe (百會: GV20), but his MCIS couldn’t accept and analyze the light in detail. So to speak, when the net of sieve is too large, too many grains are sifted out, and when the net of sieve is too fine, too many chaffs are not sifted out. The MCIS of Mr. AXE has such a structural contradiction, like a sieve that filters the information very poorly.

1. Inefficient Structure to absorb light

The first gate that light enters through Baeg-Hwe is set to be large but the tube that accepts the light into the body is very narrow. So the actual usage is very small. Therefore, no matter how much light comes in, it cannot be stored efficiently.

2. Lack of Subtlety in Thinking

When light enters in bulk, Mr. AXE’s MCIS doesn’t have the analytical unit that can divide the light finely. So, his Meta-board lacks subtlety in analysis.

3. Unsophisticated Thinking

When some information comes from the outside, it is set to crash or react very roughly in the Meta-board.

4. Overstatement and amplification of information due to increasing energy

The energy of Consciousness Cords and Emotion Cords enters the Meta-board through each cord lines. But in Mr. AXE’s MCIS, as it gets closer to the Meta-board, the energy increases and is overstated. Then, Meta-board reacts to the overstated energy and draws a conclusion by actively tossing and turning. Therefore, he couldn’t be aware of trouble in himself. If Meta-board reacted slowly with less energy, he would rather be seen a dull person of perception or thought. But his Meta-board reacts too actively to recognize his contradictions.

As mentioned above, it was the problem of Mr. AXE’s MCIS.

The Zero-Point Adjustment of Mr. AXE’s MCIS

From now on, we’ll start the Zero-point Adjustment of Mr. AXE’s MCIS.

The contradiction of Mr. AXE’s MCIS is as follows: When light is poured into his body in large quantities through Baeg-Hwe (百會: GV20), the tubes to Simpo (心包; invisible outer layer of heart) are connected at once so that the light reaches Simpo immediately.

At first glance, the tube looks large because of its high energy consumption. But the actual capacity of the tubes is small for manipulating the intangible devices and interpreting information from the universe. So the light for Zero-Point Adjustment should expand the capacity of the tubes.

Now we explain how the information from the universe is implemented:

First, enough energy (light) should enter the body. Then, the light shall reach Consciousness Cords or MSIS (Meta Structured Interpretation System) to bring out information and transmit it to Meta-board.

However, the problem with Mr. AXE’s MCIS is as follows:

The amount of light entering the body was so small that it could not reach Consciousness Cords or MSIS. Therefore, it is difficult even to get the information out of Consciousness Cords and to interpret information from universe. In conclusion, the state of Mr. AXE's consciousness has been bound to be a down-to-earth realist.

So the light for Zero-Point Adjustment is now working on extending the “Baeg-Hwe-Simpo tube” to ensure that light is fully transmitted to Simpo (心包; invisible outer layer of heart) or MSIS.

The light for Zero-Point Adjustment cleans and expands the “Baeg-Hwe-Simpo tube”. The amount of Light to be delivered to Simpo is only about one-fifth the size of Simpo. This will be modified later. The thickness of “Emotion Cords-Meta-board lines” and “Consciousness Cords-Meta-board lines” were so varying. The light for Zero-Point Adjustment is going to modify the problems so that those lines are to be “sharp and refined”. To match this, Meta-board is also modified to be slim and compact. It means that Meta-board would be no longer overuse energy and increase its efficiency.

It’s not always good to have a thick line. The thick lines are being replaced now by the less-extruded and newest specification.

The tests on slim and sharp Meta-board ended without any problem. There was no seal inside Simpo. So the light continues to flow along the tube into Simpo now, not only filling one-fifth of Simpo.

After a few minutes, the light filled Simpo well. The light for Zero-Point Adjustment is working “Meta-board-Occipital line” to the same specification as “Simpo-Meta-board line”.

At last, the light for Zero-Point Adjustment modifies MSIS. The shape of Mr. AXE’s MSIS is a scroll. It has never been unfolded and connected with Simpo. The light for Zero-Point Adjustment connects MSIS to Simpo. This concludes the Zero-Point Adjustment of Mr. AXE’s MCIS.

*Translated by SNY. Edited by Metrica.